Copyright 2002-2004 ADMtek, Inc. CPU: ADM5120-175MHz SDRAM: 16MB Flash: NOR-4MB Boot System: Linux-2.4.18-5120 Loader Version: 1.02.00 (VDSL2) Creation Date: 2005.08.03 Press key tree times to enter boot menu.. 0 Booting Linux... NOR Flash 4MB ... Kernel decompress ... Kernel decompress done ... PASS Timer irqdisable.. LINUX/5120 started... CPU revision is: 0001800b Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes. Primary data cache 8kB 2-way, linesize 16 bytes. Linux version 2.4.20_mvl31-ADM5120 (root@ADM5120-Linux) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-110.1)) #1074 Mon Jul 23 20:07:30 CST 2007 Can't analyze prologue code at 8002443c am5120_setup() starts. System no PCI BIOS Determined physical RAM map: memory: 00c43000 @ 003bd000 (usable) Initial ramdisk at: 0x801c1000 (1925120 bytes) On node 0 totalpages: 4096 zone(0): 4096 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/ram0 console=ttyS0 CPU clock: 175MHz Calibrating delay loop... 174.48 BogoMIPS MIPS CPU counter frequency is fixed at 87500000 Hz Memory: 12368k/12556k available (1603k kernel code, 188k reserved, 1976k data, 64k init, 0k highmem) Dentry cache hash table entries: 2048 (order: 2, 16384 bytes) Inode cache hash table entries: 1024 (order: 1, 8192 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 4096 (order: 2, 16384 bytes) Checking for 'wait' instruction... available. POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket LSP Revision 1 Starting kswapd Disabling the Out Of Memory Killer JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications AB. pty: 256 Unix98 ptys configured RAMDISK driver initialized: 16 RAM disks of 7110K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 1024 bind 2048) ip_conntrack version 2.1 (128 buckets, 1024 max) - 580 bytes per conntrack ip_conntrack_pptp version 1.9 loaded ip_nat_pptp version 1.5 loaded ip_tables: (C) 2000-2002 Netfilter core team NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NET4: Ethernet Bridge 008 for NET4.0 Switch Mode Port_conf2_REG: 0x3a AM5120 NOR flash device: 400000 at 1fc00000 Amd/Fujitsu Extended Query Table v1.1 at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling fast programming due to code brokenness. Creating 2 MTD partitions on "AM5120 NOR flash device": 0x00010000-0x00020000 : "BoardCfg" 0x00020000-0x00200000 : "Kernel Image" AM5120 NOR flash device initialized RAMDISK: Compressed image found at block 0 Freeing initrd memory: 1880k freed EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended VFS: Mounted root (ext2 filesystem). Freeing prom memory: 0kb freed Freeing unused kernel memory: 64k freed init started: BusyBox v1.00 (2006.05.29-14:43+0000) multi-call binary Algorithmics/MIPS FPU Emulator v1.5 mount: Mounting tmpfs on /dev/shm failed: No such file or directory Starting RAWACCESS device driver... Using /lib/modules/ifx_raw_acs (raw_acs)Init raw_acs successfully! rawdev opened! Read 34084 bytes from flash 32628 bytes...Uncompressed to...75610 bytes Write 2709 bytes to /nv/vdsl2_start.sh Write 4922 bytes to /nv/vdsl2_selfstart.sh Write 1188 bytes to /nv/vdsl2_init.sh Write 2273 bytes to /nv/vdsl2_hw_type.sh Write 2272 bytes to /nv/vdsl2_hw_type.bak Write 1074 bytes to /nv/vdsl2.conf Write 3325 bytes to /nv/udhcpd.conf Write 412 bytes to /nv/ripd.conf Write 5319 bytes to /nv/rc.iptables Write 4919 bytes to /nv/rc.firewall Write 9074 bytes to /nv/rc.conf Write 446 bytes to /nv/pptp Write 4604 bytes to /nv/pppoe.conf Write 106 bytes to /nv/pap-secrets Write 260 bytes to /nv/options.pptp Write 2398 bytes to /nv/fw_update.sh Write 15302 bytes to /nv/defconf.vdsl2 Write 129 bytes to /nv/chap-secrets Write 1277 bytes to /nv/1.sh Write 8995 bytes to /nv/rc.conf~ Write 4606 bytes to /nv/vdsl2_selfstart.sh~ Read data completely! ------------------------------------------------------------------------- SYSTEM_CURRENT_MODE_FLASH= 00000000 ------------------------------------------------------------------------- ----------------------------------------------------------------- switch mode ----------------------------------------------------------------- telnetd: bind: Address already in use Init VDSL2 CPE Ref environment - loading VDSL2 CPE Ref Board - board driver - *** Creating dir: /dev/adm5120_rb *** Creating node: /dev/adm5120_rb/0 Using ./drv_adm5120_rb Warning: loading drv_adm5120_rb will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules Warning: loading drv_adm5120_rb will taint the kernel: forced load ADM5120 Board Driver, Version 0.0.4.1 <6>(c) Copyright 2003, Infineon Technologies AG - loading VDSL2 CPE board - DFE driver - *** Creating dir: /dev/vinax *** Creating node: /dev/vinax/cntrl0 *** Creating node: /dev/vinax/0 Using ./drv_vinax Warning: loading drv_vinax will taint the kernel: non-GPL license - proprietary See http://www.tux.org/lkml/#export-tainted for information about tainted modules Warning: loading drv_vinax will taint the kernel: forced load <6>VINAX Driver, Version 0.1.0.2 <6>(c) Copyright 2005, Infineon Technologies AG <6>### VINAX - VINAX - VINAX - VINAX ### <7>VINAX_DRV: create proc config entry --> Add VINAX tick to timer queue board driver loaded <7>ADM5120_RB_DRV: MPMC init - WS RD/WR 0xC/0xC, timebase 12,5 ns <7>ADM5120_RB_DRV: address mapped: Boot Params 0x1fc10000 --> 0xbfc10000 current HW type is CO_MODE +++ unpack CO firmware +++ +++ setup CO firmware vco_hw.bin +++ MEI driver loaded init MEI driver (base addr = 0x10C00000, IRQ = 4) <7>VINAX_DRV: VINAX_IfxRequestIrq(IRQ = 4, .., ), lock = 1 !!! RESET the VDSL2 device (via MEI) !!! set VINAX DFE config VDSL2 pre init done telnetd: bind: Address already in use telnetd: bind: Address already in use Setting Hostname: VDSL2_CO.hiljanen.com telnetd: bind: Address already in use 0 tmpstaticRoute = BusyBox v1.00 (2006.05.29-14:43+0000) multi-call binary Usage: route [{add|del|delete}] 0 telnetd: bind: Address already in use telnetd: bind: Address already in use Switching Mode - Skip ADM1 config Starting DNS Proxy .... telnetd: bind: Address already in use ERROR: The /etc/dnrd directory should only be user writable Starting HTTP Server .... Using /ctl/admmod.o Loading ADM driver... -n Current Time: Thu Jan 1 00:00:09 GMT 1970 VDSL2 initialisation - post Start VDSL2 CPE Ref environment Start VINAX firmeware download --> test: open device: /dev/vinax/0. Start Download , size: 549012 VINAX_DRV[00]: Wait for 1. response - already alive (state 3) <7>VINAX_DRV[00]: start FW download - entity 0, FW imageId 0. <7>VINAX_DRV [00-01]: FW download done (bm 7) Start VDSL2 DSL DAEMON Application DSL: start DSL daemon. telnetd: bind: Address already in use Profilelist 7 30A Autostarting the line: param 30A telnetd: bind: Address already in use CURRENT_VDSL2_ProfileList = 7 CURRENT_VDSL2_BandPlanList = 19 CURRENT_C0_D_MAX = 102400 CURRENT_C0_D_MIN = 64 CURRENT_C0_U_MAX = 102400 CURRENT_C0_U_MIN = 64 CURRENT_C0_U_INT = 1 CURRENT_C0_D_INT = 1 CURRENT_VDSL2_U_SNRM = 60 CURRENT_VDSL2_U_MAX_SNRM = 61 CURRENT_VDSL2_U_MIN_SNRM = 30 CURRENT_VDSL2_D_SNRM = 60 CURRENT_VDSL2_D_MAX_SNRM = 61 CURRENT_VDSL2_D_MIN_SNRM = 30 30A nReturn=0 nLine=0 nReturn=0 nLine=0 nChannel=0 nDirection=0 nReturn=0 nLine=0 nChannel=0 nDirection=1 nReturn=0 nLine=0 bandplan 30a nReturn=0 nLine=0 nReturn=0 nLine=0 nDirection=0 TARSNRM=60 MAXSNRM=61 MINSNRM=30 nReturn=0 nLine=0 nDirection=1 TARSNRM=60 MAXSNRM=61 MINSNRM=30 nReturn=0 nLine=0 nDirection=0 nReturn=0 nLine=0 nDirection=1 nReturn=0 nLine=0 nReturn=0 done VDSL2 post init done NV-600L VDSL2 CO Board Image V 1.4.9.6 (CO) FW: v9.5.3.15.0.2 DSL-API: v1.4.6.1 DFE-Drv: v0.1.0.1 WEB-Interface: v0.3.0 telnetd: bind: Address already in use ------------------------------------------------------------------------- ------------------------------------------------------------------------- Addr: 1200007c, value: bfffffff BusyBox v1.00 (2006.05.29-14:43+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. / #